Full Batten MAINSAIL AND MIZZEN MEASUREMENT SHEET
Yellow Boxes Information SHOULD be given     Blue Boxes Information optional
Rig dimensions in metres:
Main:	P	m	E	m
Mizzen:	Py	m	Ey	m
Backstay adjustable		- yes no	Mast	- straight curved
Max. Curvature		cm	Position Half Height P?		- yes no
Notes:

Reefing hook:	- yes no
Outhaul Car	- yes no
A: Back of mast to centre bolt	mm
E :Top of boom to centre bolt	mm
D :End of boom to centre bolt	mm
B :Top of boom to centre bolt of outhaul car	mm
F :Width of outhaul pulley / shackle	mm
G :Width of tack eye	mm
H :Back of mast to reefing hook	mm
I :Top of boom to reefing hook	mm

Luff: battenslide car system

- yes no

If yes, give details on next page see Fig 10.. For other luff systems see - Fig. 3

LUFF attached to mast width:

1 (boltrope) 2 3 4

in Fig. 3

A=

mm

B=

mm

C=

mm

D=

mm

Slide model No.:

Length

mm

FOOT attached to boom with :Free-flying foot:

- yes no

or

1 (boltrope) 2 3 4

in Fig. 3

A=

mm

B=

mm

C=

mm

D=

mm

Slide model No.:

Length

mm

Mast (make):

Boom angle standard 88°

- yes no

or

°

or straightline dist. from head (mast) to clew (boom)

m

Remarks: If you have reefing hooks on your gooseneck  fitting as shown in Fig. 4 and 7 we fit standard reefing  rings on the sail - see Fig. 13   If you have no reefing hooks on your gooseneck fitting  we can fit a pressed eye with webbing band and two  st. st. rings - see Fig 14.
Type of fitting: A	- yes no	B	- yes no	(no extra change)

Remarks:
Please note that when a mainsail has full length battens there is usually a larger roach (leech curvature) and the leech should have backstay clearance (to avoid chafing when tacking). Check your existing sail or in the sailplan to see that this clearance space is available. If you are unsure, please contact us for more information or send us your sailplan.

Remarks: We deliver F/B mainsails excluding battens and cars.
We can advise you about where you can order battens and cars if necessary.

Alternatively, if you already have a F/B mainsail and you wish to re-use the existing fittings and battens, then we would require the following information:

number and type of full length battens

length of each batten

number and types of batten cars and intermediates, and headboard car type

number and type of leech fittings for battens

Fill in these relevant details in the following list.

Full Batten Mainsail - extra measurements: Length of each batten (from top to bottom) Round or Flat Only complete this section (1 - 6) if you wish to re-use your existing battens.
1	cm	J	mm	K	mm		-yesno
2	cm	J	mm	K	mm		-yesno
3	cm	J	mm	K	mm		- yes no
4	cm	J	mm	K	mm		- yes no
5	cm	J	mm	K	mm		- yes no
6	cm	J	mm	K	mm		- yes no

J: (Fig 09) Height / Diametre of Batten		=		mm
K: (Fig 09) Width of Batten		=		mm
L: (Fig 10) Luff	Box Length	=		mm
	Box Height	=		mm
N: (Fig 10) Back of mast to luff		=		mm
O: (Fig 10) Centre axle slide to luff		=		mm
P: (Fig 10) Back of mast to centre hole of headboard =						mm
R: (Fig 11) Available width for webbing		=		mm
S: (Fig 11) Available width for fitting		=		mm
M:(Fig 12) Leech Box - yes no Length  mm Height mm